Two of Our Favorite Flies
and Instructions for Tying Them
If you don't tie, or would like to order some flies,
check out our For Sale page.

 

Above you'll see some of the local experts' favorite flies. From right top and clockwise: A chartreuse and white Clouser, Larry Haines' Mae West, Larry Haines' pilchard, Larry Haines' Crystal Shrimp, Bud Rowland's Numero Uno (which caught the largest trout ever taken on a fly rod, and lots of other records), my Mother's Day Fly, a salmon Kingfisher spoon, a black opal Kingfisher spoon, my own VIP popper, another Numero Uno, Skipper Ray's bunny tail Seaducer, A red and white Seaducer, and Skipper Ray's deer hair mullet.

 
The"Mother's Day" Fly

Daichi 2546 size 4, or Gamakatsu SS15 size 4

This is the most effective all-around subsurface fly in our arsenal, and I rarely observe gamefish rejecting this fly. It's easy to tie, as well.

The MDF features glass or bead-chain (plastic or metal) eyes either mounted behind the eye or at mid-shank; splitt saddle hackle tails, a body made from Estaz; palmered hackle; and two or four legs made from Dupont Lumaflex (Spirit River's Flex Floss). The legs will help turn the fly over so that the hook will ride up and undulate even at rest. In water deeper than a foot, use glass or weighted eyes to sink the fly. I use glass beads attached by the melted mono method, as they are a compromise between the weightlessness of plastic and the weight of brass or lead.  White, pink, orange, and chartreuse are my favorite body colors, and I like barred olive for palmering and tails.
 

Tying Instructions:

1) Tie in a tuft of hot pink or chartreuse marabou to split the tails and serve as an attractor.
2) Then tie two saddles to each side of the tuft of marabou, so that they are effectively divided by the tuft. Let them extend behind the hook about 1 1/2 inches.
3) Tie in the Estaz body material, and a long barred olive saddle hackle that you will palmer through the body material.
4) For glass bead eyes: Go forward, and tie a piece of heavy (50 lb.) mono across the hook one third of the way from the hook bend to the hook eye. Put a drop of superglue on the wraps.
5) Thread a glass bead on either side to where the eyes lie against the hook shank. Light the mono on fire and let it burn into the opening of the glass eye.  But before you light the mono, wrap your thread forward to avoid burning the thread. Put drop of superglue on the inside of the beads to secure them further to the mono. Wrap the thread around the base of the eyes to ensure that they will remain stationery, and then put a drop of superglue on the wraps.
5) Wrap the Estaz forward, and anchor with your tying thread. then palmer the long saddle forward and anchor.
6) Turn the hook over, and tie in two or four strands of Lumaflex, available from  S&J Lures in Caldwell, Texas, at (713) 861-6734, or (979) 567-7374.  Leave it pretty long, say 1 1/2 inches.
7) Tie a short piece of 30-lb piece of stiff mono just behind the hook eye so it stands angled backward.
8) Trim the mono to 1/2 inch, and add a drop of superglue, or head cement, to the wraps.  

VIP Popper 
    GamaKatsu B10S #4 or #6  
    For a tail, tie in six to eight strands of Spirit River's Flex-Floss, with a few strands of Crystal Flash.  Then, going forward, stack one bunch of deer body hair on top of hook, flare and wind forward through hair for 1/4" and then continue winding forward to the eye over bare hook shank. Tie off and cut thread.
    Prepare head from block of 6mm closed cell foam. This foam is available at craft stores in the form of blank bedroom signs that hang on a door knob.  Look for them in three-packs and larger.
    Angle both front and back faces, so that block is shorter at bottom to fit remaining hook shank.
    Push bodkin needle through bottom of block, from back to front.
    Remove bodkin needle from block.
    Push block over hook eye and make sure it fits, and will slide easily over the eye once the shank has glue on it.
    Remove the head from the hook shank.
    Put drop of Superglue on hook shank.
    Again, push block over eye. Move back quickly against deer hair, making a tight seal.
    Attach doll eyes with Superglue.